• Remote control and/or local control of your electric sun blinds,
  roll down shutters, etc.
• Micromodule with built-in relay with 2 contacts for connecting a 230V motor
• Invisible installation behind existing switches or wall outlets
• Remote control using Marmitek X10
• Local control via a 2-way momentary switch attached to the module
• Quick and easy to install and to program.

• Sunblind micromodule for installation behind a momentary switch
  or in a junction box
• Invisible installation behind existing switches or wall outlets.
  Brand and model of the momentary switch can be chosen freely
  so the SWM1P can be used in every interior and installation.
• Driving of one 230Vac motor with at most 2.5 A.
• Reacts to ON, OFF, DIM+, DIM- and extended sunblind commands.
• One free programmable address A1…P16 for operation.
• One free programmable address A1…P16 for the Preset mode.
• Preset function for programming of a preference position.
• Activating the program mode can be done by pushing the programming button for at least 3 seconds
• Possibility for controlling multiple SWM1P modules at once to one preference position using the Preset function.
• Local lock function for inhibiting the operation of the motor,
  for instance during maintenance.
• Equipped with a preset function; a position for rolling down shutters
  (e.g. a day-/ventilation position) which can be pre-set
• Local blocking position for blocking the motor during for instance cleaning of the windows or maintenance.
• Lowers, in combination with the CM15Pro computer interface, the sun blinds automatically during the day in places where the sun shines inside. This way you protect your furniture against the sunlight, keep the house cool and simulate that you are at home.
• Translation in Spanish : Micromódulo de Persiana
• Suitable for connecting:
  • One 2--way momentary switch with 2 make-contacts (Up/Down function).
  • One 2--way momentary switch with 4 make-contacts (Up/Down,Preset and Lock function). See e.g. In-wall double 2-way momentary switch

• Supply voltage: 230 V AC+/- 10%, 50 Hz
• Switching capacity: 500W/230 VAC with temperature and mounting restrictions
• Wiring required: Phase and Neutral
• Protection:
  • Continuous driving time maximum 4 minutes
  • Output temperature protected.
• Use: < 1 W
• Fuse: Radial lead micro fuse, 4 AT.
• Power consumption: < 30 mA capacitive
• Signal transmission: > 5 Vpp in 5 Ohm at 120 kHz
• X10 transmission: 1 pulse at 0° and 180°
• Signal sensitivity: 5 mVpp…6 Vpp at 120 kHz ± 4 kHz
• Signal to noise ratio: 1.35 : 1
• X10 Key codes transmitting: ON, OFF, extended
• X10 Key codes receiving: ON, OFF, DIM+, DIM-, extended, Status Request
• Connection range: Up to 2.5 mm2, tightening moment 0.5 Nm
• Ambient temperature: 0 °C to 40 °C*
• Relative humidity (non condensing): 30 to 90%
• Dimensions: 46x46x16mm (minimal depth of wall box 40 mm,recommended 50 mm)
• download brochure
• download manual

*) Marmitek modules are suitable for use in homes where the temperature in the (living) rooms under normal circumstances does not rise above 35 °C and rarely (temporarily) rises up to 40 °C maximum.

• This product is for professional use only.
  Please consult a qualified electrician if you do not have the technical skills or if you have any doubts about proper installation.
• Usage of the MicroModules in a 3 phase installation. The X10 transmitters of the MicroModules transmit the command only once for use in the phase of which they are connected. When you want to receive the commands on your other phases as well, you will need to install the FKX40 phase coupler/repeater.