• Colour security camera with high sensitivity for perfect images at low light conditions.
• The pictures can be viewed anywhere in the world with all web browsers.
• No local PC required!
• You can pan and tilt the camera and you can change the resolution and digital zoom remotely.
• With the powerful, user friendly UltraView software you can watch and operate up to 16 camera’s simultaneously everywhere in the world.
• Have images sent to your e-mail address periodically or by motion detection.
• With GPIO (General Purpose Input and Output); for instance create an image recording automatically by opening a door or switch your lighting based upon (HW/SW) motion detection.
• Simple installation with enclosed software.

The IP Robocam 10 is a colour surveillance camera with a built-in computer that has its own IP address.
This allows you to connect the camera directly to a network and to access it remotely using any PC, even via the internet. That makes the camera ideal for remote surveillance of e.g. your home, shop, waiting room or reception. Also suitable for remotely attending events you would otherwise have to miss, i.e. a newborn grandchild, a school production or an important product launch.

• Large surveillance area:
  
  The camera can be panned or tilted by remote control.
  The Pan&Tilt function also makes it possible to panned or tilt the camera remotely, allowing you to view the area in which the camera has been positioned. The resolution and digital zoom can also be adjusted remotely. The software that comes with the camera offers further possibilities to save images onto the hard disk of your PC.



• E-mail notification
  
  The camera can be programmed so that it sends images periodically to your e-mail address. Using the software, the camera can also be programmed so that you receive an e-mail automatically when it detects movement.



• Accessing Cameras Over the Internet
  
  If your home or business LAN is connected to the Internet through a high speed (broadband) Internet connection, with at least 128 kbps upload bandwidth, you can access your cameras by web browser from anywhere on the Internet.
  To do this you need to:
  1. Know your WAN (Internet) IP address. This is the IP address that your Internet Service Provider gives you to access the Internet. It may be static (always the same) or dynamic (can change from time to time).
  2. Make sure the two ports used by the camera (80 & 1600) are forwarded by your router or gateway to the camera.
  3. Make sure your camera’s default gateway is set to the LAN (local) IP address of your router/gateway.

FAQ

• Q: Can the camera be installed and work if a firewall exists on the network?
  A: If a firewall exists on the network, port 80 is open for ordinary data communication. However, since the camera transmits image data, the default port 8481 is also required. Therefore, it is necessary to open port 8481 of the network for remote users to access the camera.



• Q: Can the Internet Camera be used out-doors?
  A: No, the camera is not weatherproof. You can purchase the Outdoor Dome Housing with Heater/Fan to make this camera suitable for outdoor use.

General

• Dimensions : 110x124x101mm
• Camera : 1/4” colour CMOS, 640 x 480 pixels
• Lens : F/No 2.8, 4.6 mm :
• Minimum illumination : 0.1 Lux (Starlight view)
• View Angle (Diagonal) 60°
• Pan/Tilt : Pan 330°, Tilt 105° (90° up)
• Compression MJPEG, 5 levels
• Frame rate : Max 30 fps (frame rate depends on the video format and network performance)
• Resolution : 160 x 120 pixels, 320 x 240 pixels, 640 x 480 pixels
• Power : 12VDC 1.5A, 230 V, <10 W. Power adapter included
• Temperature for use : 0°C / +45°C

Communication

• LAN port : RJ45, 10/100Mb auto-sense, auto MDI-X
• Protocol : TCP/IP, UDP, ICMP,DHCP,NTP,DNS,DDNS, SMTP,FTP, HTTP, PPPoE, UPnP
• Events Triggered by : Motion detection (2 scalable windows), GPIO or according to schedule
• GPIO : 1 input (9~40 V DC) and 1 output (240VAC, 70 mA max)
• Image Upload/Send : over email, FTP
• Image format : JPEG

Software

• Web browser: Configured standard web browser with ActiveX and Java (multi password protected and WEP, WPA protection)
• Application software: UltraView (to view 16 cameras simultaneously)

Minimum System requirements

• General
  • Hardware : CD ROM drive
  • Operating system : MS Windows 2000, XP, Vista
  • Connection Wired : 10 Base-T Ethernet or 100 Base-TX Fast Ethernet
• Camera (viewing by webbrowser)
  • Processor Intel Pentium 3, 350 MHz or above
  • Memory : 128 MB RAM, 5 MB free disk space
• Web browser : Supporting ActiveX and Java
• Ultraview Software
  • Processor : Pentium 3, 800 MHz or above
  • Memory : 512 MB RAM, 500 / 1000 MB free disk space
• Manuals (zip file : 6,6 Mb)